• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. As opposed to aluminium and timber they do not corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will help avoid unnecessary repair costs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and may even be fatal. You should take the time to ensure that your windows are in good condition.

For single pane windows it can be relatively simple to replace them, and the replacement will usually fit inside the frame that was previously installed easily. If windows with Double Glazed Window Repairs Near Me panes are held together by internal beading, it will be difficult to remove and replace the old panes. In this situation, it is necessary to buy plastic spacers to aid in fitting the new pane into the window frame.

Wearing eye protection and thick gloves is a must when you are planning to remove the glass yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall onto the fabric and not on the floor, where they could be trampled under.

After the glass has been removed, it's a good idea to cover the gap with packaging tape or duct tape to prevent water and drafts from entering the home until a professional is able to come out and fix the window. This also serves as an obstruction to prevent intruders from making their way into your home. If the gap is large, you might think about a security door that has an integrated window, as it offers the best of both worlds.

2. Sagging

uPVC windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber windows with sash. However, over time they can suffer from a variety of issues like sliding. A sagging uPVC window can cause issues with light, draughts, and even security. If you find that your uPVC window is beginning to shrink, it's important to act quickly to stop the issue from getting worse.

To repair a window that is sagging, you can try repositioning the hinges. First, you'll need to open the windows to access the frame. Then, using a screwdriver, you can remove the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Once you've repositioned the hinges, close your window and test it for fitting. If you're happy with the fit, tighten the screws until they stay in place.

If you are unable to move the hinges, you may have to replace the seal. Over time rubber seals can lose their elasticity and dry out which causes them to lose tightness. It is crucial to replace your seal as soon as you can to keep your uPVC window waterproof and draughtproof.

uPVC handles can also loosen up. This is typically caused by screws that have been removed over time, but it could also be caused by the handle mechanism getting worn out. It's relatively simple to fix a loose uPVC hand. First, you'll need to shut the window and perform an experiment fitting. The corners of the sash must be aligned with the casing joint. If it doesn't, you can use a screwdriver or a wrench to loosen the handle, and then reverse the mechanism back into its original position.

3. Water Leaks

It is essential to take action if you wake up every morning to discover mouldy walls and wet floors. Windows that leak water do can not only cause destruction of your home's structure but also hinder your efforts to control the temperature inside your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Depending on how severe the issue is, old caulking may need to be removed. When it comes to uPVC repair, you must be careful not to over-caulk. This will only make your window more difficult to clean and decrease its energy efficiency.

Check that any drainage holes have no debris in them, and also ensure that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you might have to consider replacing the window.

Mold spots and rotten sills are also signs of water leakage. The is a fungus that thrives in damp conditions and is able to quickly spread throughout the house.

If the leakage is occurring between the double glazed window repairs-glazed window, it is more likely that the issue is more with the seal than the frame. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges could be at fault if your uPVC window is difficult to open or if it opens in a breeze. They can be easily replaced by any competent DIYer and are usually done within a few minutes.

Like any mechanical part hinges are prone to be damaged over time. It's very simple to change the hinges on a window however it is simpler if you have someone to help hold the frame.

It is also important to ensure that the uPVC hinges are being opened and closed in the right direction. Check for the arrows on each hinge to determine which way the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window in a particular manner or because of inadequate installation at the factory. It is usually possible to fix the issue by sending us a photograph through our website and we will be more than happy to give you advice.

It is also crucial to ensure that the hinges are lubricated regularly. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also lower the possibility of a window sticking and help prevent corrosion. Ideally, you should perform this every year. WD40 or other solvent-based oils should not be used as they can damage your uPVC windows.

5. Draughts

Draughts can be caused by different factors. First, the hinges due to wear and tear can become misaligned, this will cause gaps to develop where the sash meets the frame. If they are beyond repair, it might be necessary to get them re-aligned. In addition, the interlock could also become misaligned. This is located on the hinge's side, and could require to be cleaned. In some instances it might be necessary to replace them.

The second most frequent cause of draughts is the window seals. These are prone to wear or damaged over time and let air escape through the gaps. Installing high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the upvc window with low-emissivity glass. this will help to regulate indoor temperatures and again will reduce the risk of draughts.

Lastly, one of the most effective ways to reduce draughts is by using a draught excluder. These are usually fabric tubes filled with some sort of filler and can be placed on the top of your windowsill. They will help stop cold air from entering and keep your home warm and cozy!

With a bit of regular maintenance and repairs your windows made of upvc will provide a great level of security and insulation for your home. It is crucial to realize that windows last for a certain period of time and there may come an point at which it is more cost-effective to replace them rather than repair them. If you are experiencing problems with your upvc windows, it's recommended to seek help from a professional immediately.