• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock replacement is a simple and affordable way to improve your home security. However, this process is not for all. It requires a certain amount of patience and expertise.

The cylinder is contained within the knob body. The cylinder is responsible for recognizing the key as it is inserted into the lock.

Removal of the old lock

First, remove the double glazing window lock repair lock repair cost (you could look here) that was previously in place. It's a simple process, but you should keep some things in your mind. Make sure that the new lock fits your door. This will ensure it is securely fitted and won't create a gap around the latch or deadbolt.

Once you have removed the latch plate, look for two bolts or screws on the inside of the casing that connect the casing and halves of the lock together. Remove them with the help of a screwdriver, and then remove the lock from the door. If you have a mortise locking mechanism, there is a set screw that binds the handle to the spindle. Make use of a screwdriver for removing this screw, then remove the doorknobs.

Remove the deadbolt as well as the latch plug from the door jamb. Install your new lock. If you're replacing a mortise you should measure the distance between your lock's case and your door's edge to make sure that your new lock fits.

Several reasons might prompt you to replace your door lock, for instance being concerned that someone else may have the key or welcoming the arrival of a new roommate. You can save money if you remove the lock yourself, instead of hiring for a professional. The process is easier than most people think, and it can be completed in just a few minutes.

Start by getting rid of the handle and trim from your door. With a flat screwdriver pry off the trim. It should be possible to pull off the majority of it. In some instances, you may even be able remove the handles completely. Next, look for a pinhole on the inside of the handle, and insert straightened clips into it. This will trigger the release mechanism and allow you to take the handle from the door. Then, look on the inside of the lock to find a small tab and press it using a screwdriver that is flat. After the spindle has been removed, you can remove the housing and the cylinder.

Selecting a new lock

There are many options to choose from when it comes to selecting a new lock. Take a look at various types of locks, and find one that matches your door's style. Consider the backset which is the distance between the edge and the center of the hole in the lock. Also, consider the cross bore, a small hole at the edge of your door frame. Also, make sure to choose a lock that will accommodate the door's thickness as well as swing.

Most door locks have been assessed by BHMA and the American National Standards Institute to give you an idea of how well they are able to withstand the rigors of use and how difficult to pick or disable. A lock grade 3 might be the ideal choice for a tranquil apartment complex in the country, while a lock of grade 1 could be more suitable for the busy streets near the storefront.

Most smart door locks require a digital key code to open. If you are concerned about hacking, or other security concerns, speak to an expert locksmith.

Replace the cylinder

It is easy to replace window lock damaged or broken doors lock cylinder using an easy DIY project. It is important to select the right cylinder and follow the instructions. First, you must remove the handle or knob if it is present. Then, using a screwdriver, unscrew the trim that surrounds the lock cylinder. Once the trim has been removed, you will be able to access the screws that hold the cylinder in place and remove them using a flathead screwdriver. The cylinder can then be gently lifted out of the door.

Be sure to measure the length of your new cylinder prior to installing it. With a tape measure, determine the distance between the cylinder's center and its right and left sides. Then, you can purchase a new cylinder with the same measurements. This will stop cylinders from snapping when doors are kicked or the key gets stuck inside.

Install the replacement locks for double glazed windows cylinder into the door and then turn the key. This will ensure that the cylinder is in alignment with the carrier, which is usually located on the outside of the lock. You can then loosen the set screws, which should be a couple of turns in the head. If there is a screw located on the outside of the case that is holding the door, you'll need to remove it.

After taking the lock cylinder out after which you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. Reinstalling the piece that connects the cylinder to an indicator stem for a lock is also essential. It is done by pulling three tabs in the back of the cylindrical using needle-nosed pliers. Attach the smaller bracket to the cylinder's back. You should then reinstall the strike plate and latch plate, along with the retaining rings fixed to the top of the lock the cylinder.

Installing the new lock

If you're replacing an old lock, start by measuring the width of the door. The majority of residential locksets come with a thickness of 3/8 inch to 1 3/4 inches. If your door is more thick, you will need a door kit that is thick and includes longer screws, a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

Most locks come equipped with a thorough installation guide to assist you. Take the time to read the instructions before beginning the process to ensure that you are following all of the necessary steps. The guide will give you a good idea of the level of skill that is required to finish the task. It is possible to ask a person who has had experience in changing locks for help if you are changing locks for the first time.

Before installing the new lock, it's recommended to cover the openings with tape the old hardware. This will keep the screws from slipping out of the holes and will protect any tiles you might have installed in the area. This will also protect your tiles from damage caused by rust, dirt and grime. SECURAM Touch comes with the masking strip or gaffer tape, but you can use any tape you own.

After you have removed the screws holding the interior portion of the lock section to the outside side, pull it straight away. It is important to do this quickly so that the lock doesn't end up accidentally closing on itself and harming the mechanism.

Fit the new latch bolt into the upper cross bore of your new lock, if it comes with one. Make sure that you place it in the correct position, which will be indicated by an arrow. Then, place the latch plate over the bolt and screw it in the correct position.

Screw the deadbolt to the jamb on the door. Try the deadbolt a few times, throwing it around to make sure it extends into the strike plate. If you're using an electronic smart lock, make sure to follow the instructions for programming it. This involves downloading an application, entering your email address, confirming your identity, and accessing the wireless network to add your device.