• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Repair an Ignition Lock Cylinder

If your car's keys isn't turning, it's time to change the ignition lock cylinder. Unlike the switch, which is the electrical component of the ignition system, which sends power to your vehicle's engine The lock cylinder is the mechanical tumbler your key is able to slide into.

Over time, "wafers" can break or wear out. Utilizing WD-40 or graphite can temporarily fix the problem however replacement is the only way to fix it permanently.

Removing the Steering Column

Most modern cars no longer have a steering column lock cylinder. They use a key to start the vehicle by pressing and turning an electronic switch located in the dashboard panel. This newer system works much more efficiently and is less complicated than the lock-cylinder system of the past. Some older vehicles still employ the old lock cylinder. If this part is damaged, it might be necessary to replace it to get the car started. This is a task that should be left to professionals.

Remove the trim panels that cover the upper and lower column of the steering with the help of a screwdriver. This will allow you access to the area around the steering column.

There is an Allen head bolt on the side of the steering wheel closest to the driver. This bolt holds the wiper/signal unit in the correct position. Unscrew this bolt and place it aside. Depending on your car's year, you may find 3 or 4 small screws with flat heads, which hold the plastic over the turn-signal switch in place. Unscrew these and set them aside.

To get to the lock cylinder, you will need to dismantle the wiper/signal assembly. You can either use a special tool to remove it or ghetto it using the help of a piece of metal, for example a cold-chisel. A locksmith will also be equipped with a shear bolt removal kit.

If you are unable to insert the key into the ignition switch the lock cylinder might be stuck. You can call a locksmith or insert the key into the ignition switch and move it to the ACC to release the pin on the lock cylinder.

Locksmiths can use a shear tool to take off the lock cylinder. They can make use of a torch to slit the pin, then shave it down to take it off. They can re-key the ignition cylinder to ensure it matches the keys you already have. This will save you money on an entirely new ignition.

Replace the Ignition Cylinder

The ignition Cylinder is the cylindrical mechanical component which houses and locks your car's key. The cylinder is affixed to the key and "reads" anti-theft code to allow or denial of the starting of your vehicle. As time passes the cylinder wears out. It could be bent or broken. In this case, you will need to replace the cylinder to get your car started.

The signs of a damaged or worn cylinder can be seen in problems when turning your key or the ignition switch not moving into the ACC or RUN position, or a warning light appearing on the dashboard. If you have a spare, try using it inside the lock. You might be able to finesse the cylinder with some graphite or WD-40, however this method only works for a limited time.

If you have a new key you can replace the ignition cylinder and follow the steps outlined above to install it. When installing the new ignition cylinder ensure that it is installed in the flange of the steering column tube, and that it is correctly aligned with the keyway on the shroud for the steering column. Check the manual of your car or an expert to make sure that the cylinder is properly aligned.

Once the cylinder is installed and the key is turned to the ACC or RUN position. Watch for a click which indicates that the ignition switch is fully seated within the cylinder. If your vehicle has an anti-theft device, you'll need to follow the anti theft relearn procedure to programme the new ignition cylinder with your key.

Some experts suggest replacing the ignition cylinder since it is typically required to shut off the airbag inside the steering column to access the cylinder. Additionally, the replacement will likely involve taking off and replacing the steering wheel and ignition covers. This is why it's best to let a mechanic with experience. They'll be able to take off the cover for the steering column and install a brand new ignition lock cylinder in your vehicle. They'll also ensure the ignition lock cylinder has been programmed with your key and that it begins to work correctly when you insert it.

Installing the Ignition Cylinder

While ignition lock cylinders are becoming less necessary in modern vehicles due to advances in push-to-start and remote start systems, they are still common on older cars. If you're having trouble starting your car or the ignition switch is not working it could be due to a defective ignition cylinder. Luckily, it's relatively easy to replace your car's ignition lock cylinder and repair the problem.

The ignition cylinder is the mechanical part of the system that slides into the ignition switch of your car and supplies power to the rest of the engine. The ignition switch and the ignition cylinder are two separate components. The switch is an electrical component that connects to the computer in your car to transmit signals to turn on the engine when you turn the ignition key.

Pins on ignition lock cylinders move upwards and downwards, allowing your key to move and rotate within the cylinder. Every movement of the cylinder and the key creates a little friction that keeps the key in place but in time, these tiny movements could cause the wafer tumblers to wear down. When the tumblers have worn down, your car's key won't be able to slide into or rotate the cylinder.

A worn-out ignition cylinder is usually the first indication of trouble in the majority of vehicles. However, the key can also begin to stick and become difficult to insert or remove from the ignition cylinder. These are all signs that the ignition cylinder lock repair lock cylinder needs to be replaced as soon as possible.

It's not a big deal to change your ignition cylinder, however, you should only do it if you are confident that you can follow the proper procedure for repair Ignition lock cylinder your car's specific make and model. You can complete the job quickly and accurately with a complete repair guide for your vehicle. If you're not confident installing the ignition cylinder yourself make one of our ASE certified mobile mechanics complete the repair for you at a time and in a location that's convenient to you.

Test the Ignition Cylinder

The ignition lock cylinder, also referred to as the ignition lock cylinder, is a mechanical device that fits your key to allow it to turn and start your vehicle. It's located inside the ignition switch, which locks the ignition and reads the anti-theft code to permit the key to turn. The ignition lock cylinder will wear out and eventually fail. This can cause problems with the vehicle's power supply or make it difficult to insert and remove keys.

The most obvious signs that your car's lock-cylinder is in danger of failing is difficulties in starting it or areas where the key gets caught when you turn it. These issues usually indicate that the cylinder is worn out and requires replacement. You might even notice a warning light flashing on your dashboard to indicate an impending failure.

As the cylinder gets older, it may be damaged due to wear and wear and tear. This can cause the pins and tumblers to wear down, damage or break and prevent the ignition of your car from working. The ignition may still work in some instances if you move it around. However this could be a sign that something is not right.

You can test the cylinder of your ignition to determine whether it's worn out, or if the key has been bent or damaged. You can test with a multimeter whether there is a voltage difference between the red wire connection of the module and the battery terminal of the ignition coil. If you do not find any voltage, then the module and switch probably need to be replaced.

It is recommended to hire an expert mechanic to repair ignition lock cylinder (click for more) the ignition cylinder, since it could cost between $200 to $300. The process is made more complicated by the fact that you may have to take other parts to access the ignition cylinder, including the steering column. The replacement process may require you to disable the airbag system and reprogram your key in order to work with the new ignition cylinder. It is usually done by an authorized dealer. However, you can do it yourself if you have the proper tools and instructions.